Tire Tread Depth Chart

Tread depth is measured in 32nds of an inch. New passenger tires typically start around 10/32", and the legal minimum in most US states is 2/32". Here is the full chart, in 32nds and millimeters, and what each reading means.

Quick answer:

Legal minimum: 2/32" (1.6 mm) in most US states. Replace soon: 4/32" (3.2 mm), when wet-road grip drops off. Winter tires: many shops recommend replacing them around 5/32" (4.0 mm), because snow traction fades earlier.

Tire tread depth chart (32nds and mm)

32nds of an inchMillimetersWhat it means
12/32"9.5 mmVery deep. Common on light-truck and all-terrain tires.
11/32"8.7 mmNew tire.
10/32"7.9 mmNew tire. Typical for passenger cars.
9/32"7.1 mmGood.
8/32"6.4 mmGood.
7/32"5.6 mmGood. Start keeping an eye on it.
6/32"4.8 mmFair. Keep monitoring at every visit.
5/32"4.0 mmWinter tires: replace. Summer and all-season tires: plan ahead.
4/32"3.2 mmReplace soon. Wet grip and braking distance get noticeably worse.
3/32"2.4 mmReplace. Recommend new tires now.
2/32"1.6 mmLegal minimum. Replace immediately.
1/32"0.8 mmUnsafe and below the legal limit.

How to measure tire tread depth

  1. Use a tread depth gauge. It is cheap and far more accurate than a coin.
  2. Measure in a main groove, not on a tread block or a wear bar.
  3. Take three readings per tire: the inner edge, the center and the outer edge. Uneven wear shows up when they differ.
  4. Write down the lowest reading. That is the number that counts.
  5. Check the wear bars. These are small raised bars inside the grooves that sit at 2/32". When the tread is level with them, the tire is at the legal minimum.

Penny tire tread depth chart (penny and quarter test)

If you don't have a gauge, a coin gives a rough reading. Insert the coin into a main groove and see how much of the head is covered by the tread.

TestResultTread depth
Penny (head down)You can see all of Lincoln's head2/32" or less. Replace now.
Penny (head down)The tread covers part of his headMore than 2/32". Legal, but check again with a quarter.
Quarter (head down)You can see all of Washington's head4/32" or less. Replace soon.
Quarter (head down)The tread covers the top of his headMore than 4/32". Still in good shape.

Coin tests only tell you whether a tire is above or below two lines. They don't tell you how far below, and they can't replace a gauge in a shop.

Tire tread depth in mm

One 32nd of an inch is about 0.8 mm, so to convert, multiply the 32nds by 0.794. For example, 4/32" is 3.2 mm. In the UK and the EU the legal minimum is 1.6 mm, which is the same as 2/32".

Truck tire tread depth chart

Commercial trucks have their own rules. For commercial vehicles in the US, the federal minimums are:

Tire positionMinimum tread depth
Steer (front) tires4/32" (3.2 mm)
All other tires (drive, trailer)2/32" (1.6 mm)

Many fleets replace earlier than the legal minimum. Check your own policy and local regulations. Pickup trucks and other non-commercial vehicles follow the standard passenger-car rules above.

Deep tread doesn't mean a young tire: rubber ages even when the tire is barely used. Check the DOT code with our free tire date code checker to see how old a tire really is.

For tire shops: turn depth into a conversation

The chart is most useful when the customer can see it. Print it for the counter, measure each wheel in front of the customer, and show where each reading falls on the chart. "Front left is at 3/32" and here is what that means" is a much easier sale than "you need tires".

  • Record every wheel, every visit, with the date. Next time you can show how fast the tire is wearing.
  • Put the reading on the estimate. It justifies the job, and it protects you if the customer later says nobody told them.
  • Keep the history. A customer who sees the numbers drop over time trusts your recommendation.

OwnDesk Tire stores tread depth in 32nds per wheel with history, so the readings are there on the next visit. For the rest of the daily routine, see our guide on how to manage a tire shop.

Frequently asked questions

What is the legal minimum tire tread depth?
In most US states it is 2/32" (1.6 mm). In the UK and the EU it is also 1.6 mm. Some states and countries set different limits, so check your local rules.
How deep is the tread on a new tire?
Most new passenger car tires start around 10/32" to 11/32". Light-truck and all-terrain tires are often deeper, and commercial truck tires deeper still.
When should I replace my tires?
At the latest at 2/32", the legal minimum. Most tire shops recommend replacing at 4/32" because wet-road braking gets worse well before that, and around 5/32" for winter tires.
How do I convert 32nds to mm?
Multiply the number of 32nds by 0.794. For example, 6/32" is 6 × 0.794 = 4.8 mm.
Is the penny test accurate?
It is a rough check. It tells you whether the tread is above or below 2/32", and the quarter test does the same for 4/32". For an exact reading, use a tread depth gauge.

Track tread depth for every customer

OwnDesk Tire records tread depth wheel by wheel, with history. It runs on your own computer, works offline and is a one-time payment.

More for auto repair, tire and dealer shops